How To Remove A Crushed Oil Filter

How to Remove a Shredded Oil Filter

by Herb Holloway

tool image by CraterValley Photograph from Fotolia.com

What was supposed to be a unproblematic oil change has just gone from bad to worse. When the oil filter on your car was stuck and wouldn't budge, you tried the old trick of driving a screwdriver through the filter to go leverage and loosen the filter. The screwdriver simply ripped the filter instance, nevertheless, and now you have a shredded or mangled oil filter and an oily mess on your hands. Don't despair. Following a fairly simple procedure using a readily available tool and a few items you probably have on hand will have that shredded oil filter off and your car back on the road.

Step i

Decide which type of oil filter wrench will piece of work on your car. It depends on how much clearance is around the base--the office of the oil filter closest to the mounting surface when screwed on. If the clearance is sufficient, a band- or strap-type wrench with an attached handle volition be fine. If not much clearance is effectually the base of the filter, the project requires a wrench with a pivoting handle or one with a square drive hole made for a ratchet handle. If you plan to utilise a square drive wrench with a ratchet handle, an extension long enough to requite the ratchet handle clearance to rotate besides is necessary.

Stride two

Curve downward all pieces of the torn filter case that protrude outward. That will reduce the chance of injury and provide clearance for the band of the oil filter wrench. Use pliers to lessen the risk of cuts from sharp edges.

Step 3

Wipe excess oil from the filter case, especially around the base. Double your rag and utilize intendance around sharp edges where the example is torn.

Stride iv

Slide the band or strap of the filter wrench onto the oil filter until information technology surrounds the base of operations, right next to the mounting adapter on the engine. The base is the strongest part of the filter, fabricated of a single piece of metal thicker than the balance of the filter. Information technology will withstand the pressure of the ring or strap when yous tighten the wrench.

Tighten the wrench in the direction that will plow the oil filter counterclockwise. You may have to hold the band or strap in place with one paw until you have sufficient tension on the wrench for information technology to catch concur of the filter base of operations. Continue counterclockwise pressure level until the filter loosens, existence careful not to striking your arm or manus on sharp parts while turning the wrench. If the band or strap slips on the base of the filter instead of grabbing and loosening it, remove the wrench from the filter. Wrap a doubled-over strip of sandpaper, the guess width of the filter wrench band and long enough to wrap around the oil filter base, around the base of operations of the filter with i rough side against the filter and one rough side facing out. You can apply a small slice of tape to concur the strip of sandpaper in place. Then place the filter wrench band or strap effectually the strip of sandpaper. The sandpaper volition provide boosted traction for your filter wrench and should allow y'all to remove the stubborn filter.

References

Tips

• Later on you successfully remove the stuck-on oil filter, apply some clean engine oil to the rubber gasket on the new filter before installing, and tighten the new filter just 3/4 turn later the gasket contacts the mating surface. These tips, and changing the oil at the recommended intervals, volition help to prevent a replay of this frustrating episode in the future.

Things Yous'll Need

• Band- or strap-style oil filter wrench
• Ratchet (optional)
• Ratchet bulldoze extension (optional)
• Pliers
• Cleaning rags
• Sandpaper (optional)
• Tape (optional)

Warnings

• Don't try to change your vehicle'southward oil and filter soon subsequently driving. Permit sufficient time for the engine to cool to forbid burns from hot oil or engine parts.

Writer Bio

Herb Holloway began writing in 1989. His chief'southward thesis was published in the "American Periodical of Agricultural Economics." Holloway has written numerous enquiry publications and publishes a quarterly newsletter for the Southeastern Louisiana University Business Research Center. He holds a Chief of Scientific discipline in agricultural and resource economic science from Due north Carolina State University.

More Articles

Source: https://itstillruns.com/remove-shredded-oil-filter-7539065.html

Share this post